Logik washing machines are environmentally friendly, allowing you to save both energy and money with every wash. With anti-allergy programs that are suitable for allergy sufferers and wash periods starting at only 15 minutes, this device is a budget-friendly kitchen need!
The question is, what should you do when your washing machine isn’t functioning properly. It is possible that you will not be able to fix the problem yourself, but you will notice an error code shown on the panel that will point to where the problem may be originating. Take a look at some of the most common Logik washing machine e21 issues below.
A detailed explanation of Logik washing machine trouble codes
The fault codes shown on your appliance may differ somewhat depending on the model. The manufacturer’s handbook is the most reliable source of information on the code. See the following list for a list of Logik washing machine problem codes and their meanings:
Error 02 in the Logik washing machine
This shows that the water level in your appliance is lower than the heater, which may be due to insufficient water pressure in your appliance.
Error 03 in the Logik washing machine
Whenever the pump fails or becomes clogged, this error code will appear on the screen.
Error 05 in the Logik washing machine
This error code will be generated as a result of a defective heater or temperature sensor.
Mistake 06 in the Logik washing machine
The failure of the motor is indicated by this error code.
Error 10 with the Logik washing machine
This is the problem code that appears when your Logik washing machine is unable to drain properly. If the water drain time out indicator is displayed, it means that the washing machine has not been completely drained — generally within six minutes. There could be an issue with the filter, an obstruction in the drain hose, wires connecting to the drain pump, or the level sensor or switch.
Error 12 with the Logik washing machine
This code will be displayed if the washing machine detects an overfilling situation. While this could simply be due to overloading or using too much detergent, the majority of the time it is related to problems with the water level sensor, wiring to the water pressure sensor, or the main water supply.
Error code 21 in the Logik washing machine
When your Logik washing machine displays the E21 code, it is also an indicator that the water has not been fully emptied from the machine. The filter, drain hose, drain pump, level sensor and switch, as well as the wiring, are all components that should be inspected.
Error 30 in the Logik washing machine
The E30 error code on a Logik washing machine indicates that there is an issue with the door. This error could be caused by a malfunctioning door safety lock switch or an interlock system. Because the door must be closed firmly in order for the washing machine to begin spinning, a Logik washing machine that is not spinning could be caused by either the door lock or the door switch, and both will require investigation.
Error code 60 in the Logik washing machine
The Logik washing machine error number E60 indicates that there is a problem with the washer motor – specifically, the main drive circuit error. In addition, the motor connection block and carbon brushes will need to be checked for signs of wear and tear, which will take time. Defective cables and tachometer connections are also possible causes of the problem.
Error 61 in the Logik washing machine
This is a failure of the motor tachometer generator, which is accompanied by difficulties in the main drive circuit, which are related to the motor’s overheat protector. This could be a complicated problem, and the motor will need to be checked by a specialist for any additional problems. Another possibility is that the motor connection block, wiring, and tachometer connections are to blame for this issue.
Solution
1. Check to see that the drain hose is in the proper position.
The drain hose should not be longer than 10 cm when it is inserted into the drain.
Check your user manual or the additional installation leaflet that came with your appliance for specific installation instructions on how to set up your new appliance. You can download the user handbook.
2. Make certain that the drain height is correct.
The drain’s height must not exceed 100 cm and must not be less than 60 cm above the base of the machine, or as specified in the user manual.
Check your user manual or the additional installation leaflet that came with your appliance for specific installation instructions on how to set up your new appliance.
3. Ensure that the pump and filter are clean.
Pump and fluff filter, as well as the pump blade, should be cleaned (if the pump blade is visible, rotate it with a pencil and refit the filter). Then, without adding any soap powder, run a hot wash cycle to thoroughly clean the drainage system.
Refer to the user handbook that came with your appliance for more information on specific processes.
4. Look for any signs of a clogged drain.
Make sure that the hose that connects to the sink trap is not clogged, and that the sink is draining regularly to rule out a clog.
Examine the drains to see if they are draining satisfactorily. Make a wash with the drain hose in a bowl or sink to see if it works.
If the washing machine continues to function well after the test wash, this may suggest that the siphon/outlet is clogged – see the next section. Ensure that the siphon/outlet is free of obstructions.
Check the location where the drain hose and the hoses are connected if the drain hose has been extended as stated in the previous installation diagram (due to the reduced flow diameter, it is more likely to be blocked)
5. Inspect the drainage hose for kinks or twists that may have occurred.
It is possible that a kink or twist in the drain hose will prevent water from flowing through it. You can examine it behind the machine if you want to be sure.
6. Reduce the amount of soap powder you use.
It is possible for the level system to become clogged by foam when a large amount of soap powder is used or when a large amount of foam is created.
Manual removal of the foam from the drum is required. After cleaning the drain pump/filter, run a hot wash without any soap powder to remove any remaining residue.
Remove the washing machine from the electrical circuit.
It may be possible to resolve the issue by turning off the power to the washing machine for around 1-2 hours and then restarting the washing cycle.
If the pump is obstructed, a bimetal fuse will trip, and the pump will be turned off. When the pump has had time to cool down, it should resume normal operation.
7. Make contact with a Service Center that has been authorized.
A service engineer should be requested if none of the previously mentioned alternatives were successful in solving the problem.
Make a note of the error code that was reported and use it as a reference when requesting an engineer. However, while this will not cure your problem, it will assist our engineer in determining the root cause of the problem.
Please be advised that utilizing the appliance until the problem has been entirely resolved is not recommended. It is important that you unplug the appliance and do not re-plug it until you are confident that it is safe to do so.
Troubleshooting for Logik Washing Machines
- Buttons are not working: The child lock has been turned on. Turn off the kid lock feature.
- The door will not open: It’s possible that the water temperature or level is too high.
- If you inadvertently start the wrong software,
- To begin, push the Start/Pause button or set the Programme Dial to 0 (Off). Second, select the appropriate program, spin speed, or optional function using the Program Dial. To begin the new program, press the Start/Pause button.
- There isn’t any water visible: The water level is low enough to see through the glass.
- There isn’t any water in the washing machine: It’s possible that the water tap has been turned off.
- There’s only a smidgeon of water here: The washing machine may drain some water if you interrupt the program and then restart it. Pouring water in via the door is not a good idea.
- During washing, water is automatically provided as the level drops, and with big loads, the water may fill up multiple times.
- The washing machine isn’t spinning at all: It’s possible that the rinse hold is active. To continue, press the Rinse Hold button. If there is a little load in the washing machine, it may be
- detected as an unbalanced load and stop spinning after several attempts. Choose the manual spin option.
- During the rinse cycle, no water is added to the washing machine.
- The washing machine spins to drain any residual water from the wash before rinsing. After then, the water will fill up.
- Several times throughout the spin-dry, the drum pauses and turns.
- The door or door seal still has foam and water in it.
Hope that kanoe.info helps you deal with this problem!
