The compressor is known as the “heart” of the refrigerator because it circulates Freon (the refrigerator’s blood) through the coils. Your refrigerator will become unusable if the compressor fails – but is replacing it a good move, or should you buy a new refrigerator? A refrigerator’s compressor can be expensive to repair or replace. Not only does the compressor cost up to half as much as the refrigerator itself, but the labor cost is also significant due to the difficult nature of the job. In this post, we’ll look at whether or not it’s a good idea to repair or replace the refrigerator’s compressor. Is it possible to repair a refrigerator compressor that has been damaged? Compressors don’t stop easily or frequently, but when they do, you’re in for a lot of trouble. So how to fix a frigidaire refrigerator compressor?
Is It Worth It To Replace Your Refrigerator’s Compressor?
While a damaged compressor can be repaired, it may not be worth the effort. Replacing a refrigerator compressor includes carefully removing the Freon so that it does not escape, then removing the damaged compressor with a blow torch. The technician will then solder the new compressor in place and recharge the Freon. This will be costly.
Most professionals will agree that replacing the entire refrigerator rather than fixing or replacing the compressor is a better option. After all, each consecutive repair increases the likelihood of your refrigerator breaking.
In the Philippines, how much does it cost to repair or replace a refrigerator compressor?
Repairing or replacing a refrigerator’s compressor, as we mentioned previously, is costly.
It will cost you upwards of $5,000 just to replace the compressor. If that isn’t enough to put you off, the technician’s professional fee will set you back an additional $3,500 to $5,000+. The overall cost of repair is less than half of the cost of a new refrigerator.
Consider the following factors:
- We’ll go over a few considerations to assist you to evaluate whether or not upgrading your refrigerator’s compressor is worthwhile.
- The refrigerator’s age
- A well-maintained refrigerator can last ten to fifteen years. If the compressor fails during the first ten years (give or take), it’s better to buy a new refrigerator than to try to fix the current one’s compressor.
- Repairing newer equipment (especially one that is still under warranty) is preferable to repairing an older one. After all, repairing an outdated unit may cause it to break down again sooner or later.
- Your unit’s repair history
- Has your refrigerator’s compressor or any other component recently failed?
- If it has had a major repair at some point in its existence or has been repaired frequently in the recent few years, it will be more cost-effective to replace the entire refrigerator.
Is your device still covered by the manufacturer’s warranty?
Compressors are typically covered by a 5-year warranty (inverter compressors have warranties of 10+ years). If the compressor fails within that time frame, you will either receive a free compressor repair or replacement, or the entire refrigerator will be replaced for free.
If the compressor fails after the guarantee has expired, simply replace the refrigerator – unfortunately at your money now.
The unit’s price
While a $10,000 repair on a $15,000 two-door refrigerator is excessive, a 20,000 repair on a $150,000 high-end french door refrigerator doesn’t seem like such a bad deal.
The final decision
As a general rule, if repairing the compressor will cost half as much as replacing the entire refrigerator, it will be far more cost-effective to replace the entire refrigerator rather than having it repaired.
Also, if you want to repair your refrigerator, keep in mind that a complete replacement compressor will be more reliable than a refurbished one, although being more expensive.
Also, please do not attempt to fix this on your own. If you mess it up, your family’s safety will be jeopardized.
How to Change the Compressor in a Refrigerator
When the compressor in your refrigerator fails, it won’t work properly, and you’ll have to toss food away.
As a result, if your refrigerator compressor fails, it must be replaced. However, before you replace the compressor, compare the expense of doing so to the cost of buying a new refrigerator. It’s possible that buying a new refrigerator is a better option.
A compressor replacement is a demanding repair that necessitates welding. This is a repair that should only be attempted by experienced and/or qualified technicians. It’s also a risky repair to perform because it entails working with highly combustible gasses.
The following is a step-by-step tutorial on replacing the compressor.
Step 1: Disconnect the old compressor.
The old compressor must be removed first. To do so, follow these steps:
- Remove the refrigerator’s plug and turn off the electricity.
- Remove everything from your refrigerator. Because repairing a compressor can take a long time, storing your food in coolers is the best option.
- To get to the back of the fridge, pull it away from the wall.
- Remove the refrigerator’s back panel. To remove the panel, simply unthread the screws holding it in place, and it should come loose. Place it out of the way once it’s been removed.
- Track down the compressor. It’s on the bottom of the fridge at the back.
- Remove the cover that protects the electrical components and disconnect the power cable.
- Remove the overload protector, the relay, and the capacitor.
- Attach a perforating valve to the process tube and then release it to release the refrigerant. Make that you have enough ventilation.
- After the gas is expelled, attach a nitrogen cylinder to the manifold and inject it at a pressure of 50 PSI.
- Remove the valve from the manifold.
- In the areas where the compressor tubes have been soldered, sand them to make them abrasive.
- Disconnect the suction and discharge tubes (leave about 20-30 mm from the end of the process tube).
- Remove the compressor from the equation.
- Remove the filter from the equation. A soldering torch is required (use a neutral flame).
- You’ll need to clean the tubes if the compressor motor burns out. This is accomplished by attaching a tube connector to the suction line and then filling a cylinder with 500 ml of solvent. The cylinder is then connected to the suction line, and the end of the cylinder is connected to the solvent cylinder. Place the capillary’s tip into a container to collect the used solvent. The solvent can be injected into the system. After that, you’ll need to charge the system with nitrogen to get rid of any remaining solvent.
Step 2: Put the New Compressor in Place
After you’ve removed the old compressor, it’s time to put the new one in place. To do so, follow these steps:
Put the new filter in place (make sure you have the correct one). To begin, solder a Schrader valve to the additional connector (make sure you take the cap off before welding). Connect the filter to the condenser outlet and weld it in place. After that, you can weld the filter to the capillary tube.
Install the new compressor in the proper location.
All of the tubes should be connected to it and welded on.
Then, using a sniffer tool, perform a leak test by injecting nitrogen into them. If you don’t have a sniffer tool, you can put soapy water over them and watch for bubbles, which indicate a leak. Release the nitrogen after it has been tested. To remove air from the compressor, use a vacuum pump.
Connect the capacitor and the overload protector to the relay, then connect the relay to the compressor’s terminal.
Connect the cooling system wires to the overload protector terminals and the relay terminals.
You can now replace the cover over the electrical components.
Refrigerant should be added to the compressor (make sure you have the correct volume).
Check that all of the wires and tubes are in the proper places, and if they are, your new compressor should be ready to use
Step 3: Verify That It Works
The final step is to make sure your new compressor is operational. You may do this by just turning on your refrigerator and evaluating its functionality. If not, you’ll need to get in touch with a professional to get it looked at.
How much does it cost to repair a refrigerator?
Factors to Consider When Estimating the Cost of Refrigerator Repair
The cost of refrigerator repair is influenced by a few factors. Diagnostic fees, materials, labor, and the issue and type of repair required can all cause prices to fluctuate from the national average.
Fees for Diagnostic Services
A homeowner will pay diagnostic fees to have a specialist come to their home and identify the problem. On average, these fees range from $60 to $100. If the homeowner employs them to complete the repair, some providers will waive the diagnostic price. Noises caused by clogged drain lines, broken thermostats, and unclean coils are the most typical causes of fridge repair. These are usually inexpensive and simple to fix.
Labor and Materials
The entire cost of fridge repair is influenced by both material and labor costs. Repairing only the broken parts is usually less expensive than buying a new refrigerator, and repairing existing parts is less expensive than obtaining replacement parts. When calculating repair expenses, take into account the cost of parts, installation, labor, and service fees. Some parts and materials may be difficult to find, resulting in greater expenses, depending on the age, model, and brand of the refrigerator. Some professionals may charge an hourly rate of $45 to $120 for labor, as well as a service fee of $150 to $200. Instead of charging by the hour, some providers may charge a flat amount for the repair.
Problem and Repair Type
Any one of the many pieces that make up a refrigerator could be the source of a problem. The cost of repairing something depends on what it is, what problem it produces, and what type of repair it requires. Some of the most typical refrigerator repairs are listed here.
- $50 to $440 for a rubber door seal
- $50 to $200 for a drip pan
- Thermostats range from $100 to $440.
- Coils for condensers range from $100 to $440.
- Defrost motors range in price from $100 to $440.
- $500 to $800 for a control board
Hope that kanoe.info helps you solve the problem!