In your Maytag or Whirlpool Duet washing machine, the error number E01 F09 might show up on the screen. This could mean that there is a problem with drainage. What’s more, guess what? You don’t even need to contact a repair shop to resolve the issue. The E1 F9 error number on your Whirlpool device’s display is frequently accompanied by the machine’s inability to spin and drain properly, therefore this is the type of issue you need to fix as soon as possible to use the washer again. The problem is rather common, and most users can resolve it within minutes. We’ll go over all you need to know about error number E01 F09, its causes, and how to fix it in this tutorial. Let’s go right to the topic now!
A variety of events might result in the E1 F9 Error.
Your machine will no longer be able to pump water from the tank and will be unable to execute any further operations as a result of the appearance of this error number on the display. A drain system malfunction, which can be caused by damage or failure of one of its components, or by an obstruction, is the most common reason for the E1 F9 Error on your appliance’s screen. Your machine’s drainage system, as you may know, consists of a drain hosepipe, filter, or pump. As a result, one or more of these details may get clogged or broken. Another cause could be a temporary glitch or a substantial control panel failure; nevertheless, this is a rare occurrence that should be investigated as soon as possible.
What does the F9 on a Whirlpool washer mean?
In the display, there appears an F9 E1 code: This error code means that drain times are longer than expected, usually more than eight (8) minutes.
On a Whirlpool Duet washer, what does Code F mean?
The F/dL code indicates a machine door lock problem. When the door fails to lock to allow the cycle to begin, it makes at least six attempts to lock itself before the error displays on the digital display panel. The machine will not run if the door does not lock.
What does the Whirlpool washer code E1 mean?
The E1 error number indicates that the correct water level was not reached within 20 minutes of starting the washer.
What does the letter F on a Whirlpool Duet washer mean?
What is the procedure for resetting the code on my Whirlpool front-load washer?
Press the stop or cancel button twice and the power button once to delete the code. If the error code persists, unplug the washer or turn off the electricity for one minute. During the Clean Washer cycle, items were discovered in the washer. Restart the Clean Washer cycle after removing the things from the drum.
What do the F9 and E1 codes on a Whirlpool washer mean?
The washer is taking too long to drain water if F9 E1 (drain pump system malfunction – long drain) displays on the display. The drain may extend beyond the standpipe by more than 4.5′′ (114 mm). Check for proper drain hose installation in the plumbing.
What do the numbers E1 and F9 on a Whirlpool Duet washer mean?
Clogged or pinched hose The drain hose may slide and become stuck between parts, twist, or bend as a result of the washing machine’s vibrations. This is one of the most prevalent causes of error E1 F9 appearing on the screen. It might also become clogged due to huge debris clogging the drain.
On a whirlpool washer, what does Code F mean?
The “F” code appears on the Whirlpool Cabrio washer. The “F” code has the following meaning. It signifies the primary control has failed, and you’ll need to replace the machine control part to fix it. This error should be addressed by Whirlpool because it is a typical problem with Cabrio washers. You can call 1-800-253-1301 and Whirlpool will send a technician to fix it and pay for the part.
What is the best way to clean a whirlpool duet washer?
– Clean the gasket: Apply mildew cleanser to a towel and wipe the gasket, being sure to get behind it as well. – Clean the dispensers: Using soap and water, scrub the slide-out detergent dispensers. – Run a “sanitize” cycle: Look through the machine’s settings to see if there is a “sanitize” cycle.
What are the whirlpool washer fault codes?
A: Error codes for washing machines, such as the Whirlpool Duet front loading automatic unit, can start with an F and then two digits, such as F07, F09, or F10.
What does Whirlpool washer F21 stand for?
Whirlpool Washer Error Code F21 indicates that the washer is unable to empty water. This problem happens when the drain pump or drain hose becomes blocked with dirt and debris, causing water to become stuck and the washing machine to become unable to drain.
The E01 F09 Error Code in Your Maytag Front-Load Washer and How to Fix It
A drainage problem in your Maytag or Whirlpool washer could be caused by a variety of factors. The E01 F09 error code will appear on the washer’s display due to one or more malfunctioning drainage system components, resulting in a protracted drain time.
We’ll look into the sources of this error later, but first, let’s put your washer into Diagnostic Test Mode so we can figure out what’s causing the problem. This is how you activate this mode:
- The third button should be pressed.
- The power and start buttons should flash if you press the second button.
To start the Diagnostic Test Mode, press the start button.
After the test, the washer should be able to pinpoint the source of the issue.
Let’s look at some of the possible causes of the E1 F9 problem and how to fix them:
- Drain Hose with a Bend
- Drain Hose with a Bend
- The capacity of the washer to drain the water may be hampered by a bent drain hose. A bent hose is easy to spot, and all you have to do now is straighten it up a little. It’s advisable to replace the hose if it’s damaged beyond repair.
The drain hose height must be 96″ or higher as a side note. If it’s less, the washer won’t drain properly.
Drain Pump Issues
The washer will not drain water properly if the drain pump is damaged, resulting in the fault E01 F09 on the electronic control board. You can test the pump by doing the following steps:
- Examine the drainage system for any clogs.
- Check the pump and its connections using the Quick Diagnostics Test.
- Remove the power wire from the washer.
- Remove the top panel.
- Make that the DP2 connector in the Central Control Unit is fully inserted (CCU)
- Remove the DP2 connector and check the resistance between pins 1 and 2 with an ohmmeter.
- Continue with the next steps if the resistance isn’t around 16 ohm.
- Unscrew the front panel and physically inspect the drain pump for clogging if the reading is open.
- Check the connections to make sure they aren’t loose.
- Check for continuity between the CCU and the pump with an ohmmeter.
- Replace the bottom harness and retest the resistance if the test is negative.
- The Central Control Unit is not responding (CCU)
- If the pump and its wiring are in good operating order, an issue with the CCU could be the cause. Follow these steps to replace the CCU:
Wait a few seconds after disconnecting the washer’s power line
- Take off the top panel.
- Unplug the CCU once you’ve found it.
- Change out the CCU with a fresh one.
- Replace the top panel and any other parts that were removed.
- Perform a Quick Diagnostic Test to confirm that everything went according to plan.
- Failure of the Pressure Switch
- Failure of the Pressure Switch
- The error E1 F9 can be caused by a defective pressure sensor in your washer’s drain mode. A multimeter can be used to see if the switch is working properly.
Examine the pressure pipe to see if it’s pinched, leaking air, or clogged.
A clogged drain
An unclean drain pump filter could also be causing your washer to display the error number E1 F9. The drain catch can be accessed and cleaned by following these steps:
- Lean the washer against the wall at a 45-degree angle.
- Remove the screws from the front panel’s bottom.
- Take off the drain cap.
- The drain catch should be cleaned.
Most Commonly Asked Questions
If my washing machine won’t drain properly, how can I reset it?
There is no reset button on a Maytag or Whirlpool Duet washer. You can still reset your system by following these steps:
- Wait a few seconds after unplugging the power cord.
- Reconnect the power cord.
- To begin, press the start button.
- Start afresh wash cycle by selecting a cycle that is appropriate for your items.
- To reset the washer, use the start/pause button.
- How Do I Remove a Washer’s Error Code?
- Even after you’ve resolved the issue that’s causing the error code, the error message may persist. Press the power button once, then the cancel button twice to clear the error message.
If the problem persists, try turning off the washing machine for a few minutes.
To summarize, maintaining the drainage system is the key to resolving the E01 F09 error code on a Maytag or Whirlpool Duet washer. The problem warning should go away once you’ve double-checked that all of the drainage system’s components are working properly. The tubing, pressure switch, drain pump, CCU, and drain catch are among these components. If you’re still having trouble solving the problem, it’s time to seek professional help from the repair facility. Hope that kanoe.info helps you solve the problem.
