It can be a bummer if your AT&T TV Remote stops working, especially if you have a show to watch. You can’t afford to miss that hotly anticipated football game or that new show. You must repair the AT&T TV remote volume not working or you may miss out on your favorite shows.
What’s the deal with my AT&T TV remote?
Your AT&T TV remote’s failure to function is most likely caused by low batteries. You’ll need to change your batteries if the AT&T button on the top of your remote control doesn’t light up brightly. Replace the batteries in your remote, whether they are AAA or AA, with new, high-quality ones.
Wireless electronics such as battery radios and telephones may interfere with the signals emitted by your remote control, causing your TV to respond differently.
To solve the problem, keep all wireless devices away from your TV and remote. Any physical things that could obstruct signals from the remote to the TV sensor must be removed as well. Continue reading if none of these suggestions work for you.
How to Repair a Blocked AT&T TV Remote
At this point, you might need to reset your TV remote, which clears any programming errors and restarts the device. Follow the instructions below to complete the reset as seamlessly as possible, depending on your AT&T TV and remote control brand.
The following are the steps to use the AT&T S10, Silver, or Point Anywhere remotes:
- Keep the “AT&T” and “OK” keys pressed at the same time.
- When you let off of both keys, all four mode keys will flash twice, indicating you’re in programming mode.
- Using the remote control’s number keys, enter the programming code “900.”
- The AT&T key will flash for a long time, indicating that you entered the code properly and that the remote has been reset to factory defaults.
- The following are the instructions for using the AT&T S20 and S30 remotes:
- Using both hands, press and hold the Menu and OK buttons.
- When you let go of both buttons, the programming mode indication on your remote flashes twice.
- Using the remote control’s number keys, enter the programming code “981.” Make sure the code is entered correctly when the power key flashes four times, and the remote will reset to factory settings.
- Keep enough space between the receiver and the television; some newer models feature backlighting that can interfere with the remote-control signal.
- Make sure there’s enough space between your television and the television receiver to avoid interference.
If none of the above fixes the problem, the issue could be due to a problem with the AT&T TV’s connection to the TV remote control. Follow the instructions below to avoid this issue:
- To begin, unplug the device’s remote.
- Before the remote’s LED lights glow blue twice, press the DASH (), APPS, or Diamond keys.
- Hold down the red button on the side of your AT&T TV to restart it. Unplug and re-plug your television.
- After you’ve turned on your AT&T TV, pair the remote with it as follows:
The AT&T remote control should be pointed at the television.
- FAST FORWARD and REWIND must be pressed and held simultaneously for 2-3 seconds.
- Once the pairing is complete, your remote will display an on-screen message indicating that it is ready to use.
- After performing these steps, your AT&T TV remote should now work correctly. If these don’t work, it’s time to get a new TV remote.
- The volume isn’t controlled via the AT&T TV remote.
Pointing a remote at the television:
- If you can’t adjust the volume on your TV with your AT&T Remote, it’s cumbersome and frustrating. This problem, fortunately, has some straightforward solutions. The volume issue is usually quickly resolved by reprogramming your AT&T TV Remote.
- Press the Menu Key and select Help, then OK if your AT&T TV Remote isn’t working or changing the volume. Then select Information, Troubleshoot, and Resolve from the drop-down menus. Choose Sound, then TV. To correct the volume problem, go to Sound Issue and follow the on-screen instructions.
- To remedy the volume problem, you can alternatively use Program Mode. If you press OK and Menu simultaneously for around 3 seconds, the Power key will flash a red color twice, indicating that you’re in Program Mode. To finish the volume adjustment, press the Volume Up key, which will generate a single red blink.
- The AT&T TV remote control will not turn on or off the television.
- It’s most likely due to broken remote batteries or a problem with your TV if your AT&T Remote won’t switch on or off. Completely troubleshoot both possible causes to swiftly identify the source of the problem.
- Check to see if the remote’s batteries are charged. Replace them as needed, then unplug and re-plug the power cord to reset the television.
- Check the Mode buttons on the remote to see whether it is in TV mode, then use it to see if it turns on and off normally.
The Blinking of the AT&T TV Remote
It’s frustrating to realize that your AT&T Remote isn’t working and keeps blinking while you were watching a show and then placed it on the stop. This can be quite annoying and, in some situations, entirely detract from your viewing pleasure. With a few quick troubleshooting steps, you can remedy this problem. It’s most likely due to a Bluetooth pairing issue if your AT&T Remote isn’t working and keeps blinking. Check that your Bluetooth connection is properly functional before proceeding with the debugging. Check to see if your remote is connected to your television and if the batteries are low.
How to link your AT&T TV remote with your TV
If you have many remote controls or have recently purchased a new one, each remote control can only be used with one Direct TV streaming device at a time and cannot be swapped out without reprogramming makes sure the remote wasn’t accidentally switched. Refreshing the connection between your remote and your Direct TV equipment can help you fix a variety of problems. How to do it is as follows:
- To begin, turn off the device and detach the remote.
- Hold down the (–) and APPS or Diamond buttons until the (–) and APPS or Diamond LED lights on the remote flicker blue twice.
- To restart your Direct TV equipment, press and then release the red button on the side. Unplug and then re-plug your device is another option.
- When you switch it back on, pair the remote with your device.
- With the remote, choose your Direct TV device.
- Press and hold fast forward and rewind for 2-3 seconds at the same time. When they link, you’ll receive an on-screen indication that your remote is ready to use.
The remote Control for ATT TV isn’t working
What should you do if your ATT Remote stops working for no apparent reason? This dilemma is especially troubling if you are anticipating a thrilling sporting event or a new episode of one of your favorite Netflix shows and are concerned that you will be unable to watch it. There are a lot of possible causes for your ATT Remote not working, all of which you can easily troubleshoot to find the source of the issue and then swiftly resolve.
Check the battery level on your ATT TV Remote if it isn’t low. On top of the ATT TV Remote, press the ATT button. If the battery level is acceptable, the button should glow. Otherwise, the batteries will need to be replaced. Check if any wireless devices, such as smartphones, are interfering with your ATT TV Remote. Place all of these devices as far away from your television as possible, as well as your remote control. You can also try moving anything in your TV viewing area that may be blocking the path from the remote to the television.
It could also be that your ATT TV Remote needs to be reset. You must hit the OK and AT&T buttons at the same time to accomplish this. When you let go of both buttons, each of the four Mode keys will flash twice. This indicates that you’ve entered the programming mode for the remote.
Now type in the number 900, and the AT&T logo will flash for a long time, indicating that your ATT TV Remote has been reset to its factory default settings
The Volume on the ATT TV Remote Doesn’t Change
It’s inconvenient and unpleasant if you can’t adjust the volume of your TV with your ATT Remote. Fortunately, there are several simple fixes available. Reprogramming your ATT TV Remote usually solves the loudness issue quickly.
If the ATT TV Remote won’t change the volume, hit the Menu Key and select Help, then OK. After that, choose Troubleshoot and Resolve. Select TV and then Sound from the drop-down menus. To fix the volume problem, select Sound Issue and then follow the directions.
Going into Program Mode can also help with the volume issue. The Power key will flash a red hue two times if you press Ok and Menu at the same time for around 3 seconds, indicating you are in Program Mode. You can now press the Volume Up key, which will cause a single red blink to complete the volume adjustment.
The ATT TV remote does not work to turn on or off the television.
Check to see that the batteries in your ATT TV Remote are fully charged before using it to switch on or off the TV. Replace them as needed, then disconnect and re-plug the television’s power cord to restart it.
Then, verify sure the remote is in TV mode by checking the Mode buttons and then try using it again to see whether it turns on and off normally.
The Blinking ATT TV Remote
It’s really disturbing to discover that your ATT Remote is not working and keeps blinking when you’re viewing a show and then trying to resume watching it. This can be very distracting, and it may even ruin your viewing experience. This problem can readily be resolved with a few fast troubleshooting actions.
If the ATT Remote does not operate and continues to blink, it is most likely due to Bluetooth pairing issues. Before continuing with troubleshooting, double-check that your Bluetooth connection is working properly. Check for low batteries and that your Remote is synchronized with your TV.
Do you own a smart television from a different brand? To locate your TV brand, please read our article on Smart TV Remote Not Working.
ATT TV Remote Won’t Pair or Connect
If your ATT TV Remote won’t pair or connect, you won’t be able to change channels or control your television. Check out this fast technique to reclaim control of your ATT TV Remote because this is completely unacceptable.
Take the ATT TV Remote and aim it directly at your TV if it isn’t working or won’t connect/pair. Then, simultaneously, press Rewind and Fast Forward. You should now see a notification stating that the ATT Remote has been successfully connected to your television.
You can also try simultaneously tapping the Mode and Enter buttons. Hold them both in place for about a second before releasing them. All of the Mode buttons on your ATT Remote should be flashing twice at this point, indicating that you have entered Programming Mode and are ready to sync the ATT Remote with your TV.
Hope that kanoe.info helps you solve the problem.